Landoll ICON 800 Series Earthmover Manuel d'utilisateur Page 1

800 Series Earthmover Parts & Service

Safety Section Crushing/Cutting Prevention Support the machine properly before you perform any repairs or maintenance beneath that machine. Do not

About the ICON 821 Limited Warranty…….. The ICON 821 scraper is designed with front lowering and a push bumper on the rear. The responsibility

_______________________________________________ Mounting/Dismounting of Earthmover Hook Up

Hitch Options For The 821 Earthmover The standard hitch on the 821 is the push block #2002014 The optional

Parts Listing For 821 Earthmover Ref # Part # Description Qty 1. ICO0204

Parts Listing For 821 Earthmover Ref # Part # Description Qty 46. 400

821 Mainframe Components 25 30 29 28 56 46 44 42 47 45 43 57 58 59 60 ICO2005 2.5 x 9.5 ICO2024 Depth Gauge ICO2020 Brake Cover ICO2019 LT0058 Rear Ha

50 36 22 26 21 27 61 8 13 89

821 Mainframe Components (top front view) 56 18 1 11 20 9 37 19 14 2/3 16 23 22 13 21 8 61 66 spacers ICO2014 push block ICO0512 Coupler Ho

ICO2132

Part # Description Ref# Where Used Qty BC Bolt, Carriage 1/2 x 1 1/2” PO Wall Wear Strip (1) 12 WFH Washer, F

Part# Description Where Used Qty SCR2078 Spacer For Wheels 40 BH Bolt, Hex 7/8 x 3” Fine

Components of the 821 Push Off Wall and Frame pinned together using an ICO0420 on each side. 5000479 Grease Line Push Off Cyl. 40010

ICO2001 Depth gauge ICO2024 ICO2007 ICO0218—3/4 x 1 1/2” Shown are the brake assembly, brake line cover and the horizontal wheel-mounting clamps/bolt

Shown is the push off bearing ICO0258 and pin ICO0218. Th

Clam Pivot Pin (ICO0523) Shown is the ICO0523 Clam Pivot Pin.

Assembled 821

2000460 Shown is the 3” pin (ICO2052) used with the cast hitch. The top is milled to allow the retainer plate (ICO2051) to bolt on using (3) 5/8 x 3”

1 1/2” x 6 1/2” cast bracket ICO1055 3/4 x 2” gr. 8 cast swivel ICO1092 2000460 The Super Duty Cast Hitch uses a 3” quick attach pin ICO2052 5/8 x 3”

Ref # Description Qty Part # 1 Cast Swivel 1 ICO1092 2 Quick Attach 3” Pin Cap 2 ICO1093 3 Quick Attach

Hub & Axle Assembly Axle and Hub assembly shown with brake package. Brake assembly mounted on tire/rim Rear frame of the 821 shows the horizontal

Brake components used on the ICON Earthmovers are manufactu

Brake Components Used on all ICON Earthmovers Equipped wit

Wear Strip—ICO2162 (2 pcs) 1/2 x 1 1/2” Carriage Bolts (12) 82

ICON now installs hydraulic accumulators on all machines. The

Table Of Contents A. Product

Accumulator Valve 4001317 Valve #51 Accumulator Valve Mounting Block ICO2044 #38 ICO2042 Accumulator Valve Actuator Arm #36 2—3/8 x 2” He

Shown are the components of the Accumulator Valve and Actuator Arm This setup was standard on the early model 821’s. Later models are not adjustable.

5000793 4000924 4000623 5000833 5000424 5000793 4000925

Front view of the cylinder mounts and hydraulic shut off valve. All hydraulic connections are made at the bulkhead (shown)

Hydraulic Flow Shut—Off Valve The shut off valve is located at the rear of the tongue. It is designed to relieve the hydraulic pressure in the syst

Current valve block and fittings for Model 823 Earthmovers, be

4001452 4001451 5000793 4001450 500796 5000833 5000833 5000796

Hydraulic Components of the 821 4000921 50001013 4001420 Manu

Warning! To prevent a hazardous situation, which if not avoided can result in injury or death, read and follow these instru

Either 1/2” or 3/4” Pioneer ends may be used. This depends upo

4001309 ea. side 4001415 ea. side side graphics 4001306 4001416 4001432 usa ea. side 4000936 ea. side 4000372 4000941 4000940 4000938 4000938

4001418 4000960 ea. side 4000931 4000940 4000396 Grease Daily 4000938 ea. pin location 4000934 ea side 4001248 Grease Daily 4000938 ea. pin 4001254 40

Safety Section 3a

Decal Listing For 821 Earthmovers Complete K

ICON Industries Commercial Earthmover Assembly, Lube and Check

ICON Industries Commercial Earthmover ____1. Install cutting b

Foreword Literature Information This information should be stored in the literature holder located on the machine. This manual contains

Safety Section General Hazard Information Safety Section General Hazard Information A “Do Not Operate” warning tag or similar warning tag should be at