Landoll PT Series 10 through 20 Transport Pulverizer Manuel d'utilisateur télécharger pdf (Page 22)

2-12 9J017

ASSEMBLY

PT Series 10’-20’ Models LED Lamp

and Harness Installation

NOTE

Unless otherwise noted the following installation

instructions apply to all PT 10’ - 20’ Models.

1. Install outer Light Mount Brackets using existing

outer bearing hanger 5/8-11 U-Bolts, Lockwashers

and Nuts

2. On 10’-16’ Models install the inner Light Mount

Brackets approximately 36” from center line using

1/2-13 U-Bolts and 1/2-13 Locknuts. See

Figure 2-14.

3. On 17’-20’ Models attach the inner Light Mount

Brackets approximately 36” from center line using

Straps, 1/2-13 X 7-1/2 Screws, Washers, and

Locknuts. See Figure 2-14.

4. On the 10’ Model install the Amber LED inside the

Tube Light Shield, attach to the outer Light Mount

Bracket using four 1/4-20 X 1-1/2 Screws and 1/4-20

Locknuts.

5. On the 10’ Models install the Decal Plate Mounts to

the center frame end plate using 1/2-13 X 1-1/2

Screws, Washers and Locknuts.

6. On the 12’-20’ Models install the Amber LED inside

the Tube Light Shield, attach to the outer Light Mount

Bracket using four 1/4-20 X 1-3/4 Screws. Attach the

Decal Plate Mounts and secure with 1/4-20 Locknuts.

7. On the 10’ Models attach the Red LED to the inner

Light Mount Brackets using four 1/4-20 X 1-1/2

Screws and Locknuts. Ensure the red lens faces

rearward.

8. On the 12’-20’ Models install the Red LED to the

inner Light Mount Bracket using four 1/4-20 X 1-1/2

Screws. Attach the Decal Plate and secure with

1/4-20 Locknuts.

9. Attach the Light Module to the Light Module Bracket

using two 1/4-20 X 1-1/2 Screws and Locknuts. See

Figure 2-16.

10. Attach the Light Module Bracket to the front side of

frame using 3/8-16 U-Bolts and Locknuts.

IMPORTANT

Cords are marked “Left” and “Right”.

11. Raise the machine if not done previously.

12. Layout the LED Lamp Harness and attach the

harness to the Light Module.

13. Route the left and right 3 plug cord along the top of

the frame and connect to each Red LED Lamp.

14. Route the remaining left and right 2 plug cords along

the left and right top of frame and connect into each

Amber LED Lamp.

15. Layout the 7 Pin Harness and attach the harness to

the Light Module.

16. Route the 7 Pin Harness across the frame and along

the drawbar tube and over to hitch point.

17. Adjust the LED lamp angles so LED’s are vertical

with the drawbar height adjusted to the transport

height. Adjustment is provided to compensate for

high drawbar heights if used as a companion tool or

lower heights if towed directly behind a tractor. See

Figure 2-15.

18. Tighten all hardware.

19. Bundle and secure any excess cord with tie straps.

20. Apply the reflector decals to Decal Plate Mounts. The

amber reflector decals should be front facing on the

outer Decal Plate Mounts. The red reflector decals

and orange decals should be rear facing on both the

inner and outer decal plate mounts.

IMPORTANT

All wires must be firmly attached to machine frame

members, or hydraulic lines, so they don’t sag or

become torn loose by field debris. Use the cable and

hose ties provided.

21. Mount the SMV bracket to the Center Bearing

Hanger using existing hardware. Then attach the

SMV sign to the bracket using 5/16-18 X 1 Screws,

Washers and Locknuts.

IMPORTANT

Check to be sure that wiring at center of machine is

slack enough so as not to be stretched or interfered

with while rotating frame from transport to field

working position and vice versa.

1 2 ... 17 18 19 20 21 22 23 24 25 26 27 ... 49 50

Commentaires sur ces manuels

Pas de commentaire

Landoll PT Series 10 through 20 Transport Pulverizer Manuel d'utilisateur Page 22

Commentaires sur ces manuels

Produits connexes et manuels pour Machines spéciales Landoll PT Series 10 through 20 Transport Pulverizer