Landoll 6230 Disc Manuel d'utilisateur Page 93
- Page / 96
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
5-1
Chapter 5
Troubleshooting Guide
The Troubleshooting Guide, shown below, is included to help you quickly locate problems that can happen using your
6230 Disc. Follow all safety precautions stated in the previous when making any adjustments to your machine.
PROBLEM PROBABLE CAUSE SOLUTION
UNIT NOT LEVEL, LEAVING CENTER
RIDGE
Leveler not adjusted properly Adjust leveler, lower front gang
Hitch adjustment too low Raise implement hitch point
Gauge wheels carrying too much weight Raise gauge wheels
UNIT NOT LEVEL, LEAVING CENTER
FURROW
Leveler not adjusted properly Adjust leveler, raise front gang
Hitch adjustment too high Lower implement hitch point
UNIT NOT LEVEL, LEAVING RIDGE ON
OUTSIDE OF UNIT
Unit not level front to rear, front running too
deep
Adjust unit to be level
Wings not level with center frame Adjust side to side level. Wings should
typically be set even with or slightly
higher than center section
Operating speed too fast, front gang
moving soil past rear gang
Slow down to proper operating speed for
field conditions.
Hitch adjustment too high Lower implement hitch point
Gauge wheels too high, allowing wings to
go too deep
Properly reset gauge wheels
UNEVEN DEPTH Frame not level side to side Level center frame side to side
Wing frames and center frame not level Level wing frames to center frame
Lift cylinders not in phase Fully extend lift cylinders and hold
hydraulic lever until all cylinders are
fully extended
Lift wheels not carrying enough weight Adjust depth stop and raise implement
Fold cylinders not fully extended to allow
wings to flex
Extend fold cylinders fully.
Tire pressure too low Check inflation
Unit not level front to rear Adjust unit to be level
UNIT SIDE DRAFTS OR MOVES SIDE
TO SIDE
Lift wheels not carrying enough weight Adjust depth stop and raise implement
Unit not level front to rear Adjust unit to be level
Level unit side to side Level center frame and wing frame to
center frame side to side
Gauge wheels too high, allowing wings to
go to deep
Properly reset gauge wheels
FRAMES BUCKLING, NOT EVEN Lift wheels not carrying enough weight Adjust depth stop and raise implement
Wing frames and center frame not level to
each other
Level wing frames to center frame
Gauge wheels not set correctly or uneven Set gauge wheels properly
- Model 6230 1
- Operator’s Manual 1
- Table of Contents 3
- 5 Troubleshooting Guide 4
- Introduction 5
- INTRODUCTION 6
- Standard Specifications 7
- LANDOLL CORPORATION 8
- STANDARD SPECIFICATIONS 10
- Assembly Instructions 27
- ASSEMBLY INSTRUCTIONS 28
- 6230 Disc Frame and Hitch 29
- Assembly 29
- Leveler Assembly 31
- Manual Leveler 33
- Hydraulic Leveler (Option) 35
- Hydraulic Depth Stop Tube 37
- Fold Cylinder Mount 41
- Center Frame Tires 43
- Disc Gangs 43
- Wing Frames 45
- Hydraulic Installation 58
- Light Installation (Prior to 58
- August, 2013) 58
- 3-34 F-440-0113 Edition 60
- LED Light and SMV Bracket 61
- Rear Tow Hitch (Option) 62
- 3-38 F-440-0113 Edition 64
- Harrow Installation 65
- Final Assembly 66
- Operation and Maintenance 69
- Tractor Preparation 70
- Disc Preparation 70
- Attaching To The Tractor 71
- Hydraulic Lift System 71
- 1-3/8 x 10 TRANSPORT 72
- Hydraulic Fold System 73
- OPERATION AND MAINTENANCE 74
- IMPORTANT 74
- 6230foldlock1 74
- 6230foldlock2 74
- General Operation 75
- Field Operation 75
- APPROXIMATELY 76
- 6230levelmeas 76
- Leveling (Front-to-Rear) 77
- Hydraulic Leveler Gauge 78
- Adjustment 78
- Variable Ratio Adjustment 79
- Hitch Adjustment 80
- Scraper Adjustment 81
- Operation/Adjustment 82
- Maintenance 84
- Front Gauge Wheels 85
- DEPTH STOP TUBE 86
- DEPTH STOP GAUGE 86
- DEPTH STOP 86
- 6230depthstopadj 86
- Wheel Bearing Maintenance 87
- Hydraulic Maintenance 87
- Transport 88
- 1/8 HAIR PIN 89
- 6230translock2 89
- 6230 lube 90
- Lubrication Maintenance 91
- Storage 91
- Chapter 5 93
- TROUBLESHOOTING GUIDE 94
Produits connexes et manuels pour Machines spéciales Landoll 6230 Disc
(98 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.627 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels